Best Barns southdakota_1220 Manual de Instruções

Manufactured by Reynolds Building Systems, Inc.205 Arlington Drive Greenville, PA 16125 724-646-3775This manual is copyrighted. Under the copyright

5. Cut the 'right' siding panel flushwith the sidewall siding.3. Cut (2) two siding panels to a length of 87-3/4". Install the 'le

1. Install a gable on the rear wall. Secure gable to wall by nailing throughthe gable plate with 10d sinkers.2. Cut 1x4 boards and install as sub-trim

1. Install a 2x4-6' board over the sidewall,against the rear gable plate. Use 10dsinkers.SidewallStep 11 Install 2x4 Tie Plates2x4-6' Tie Pl

Inside of Building2x4 Tie PlateStep 12 Layout Roof Trusses1. Layout the truss spacing from the rear of the building. Measure from the backside of the2

3. Install soffit panels on theopposite side. Start with a24" long panel that has a'LAP' edge.Step 13 Set Roof TrussesRear GableStep 14

Optional ridge vent providesideal ventilation.AirSpaceTrussShingles2. Cut and install roof sheathing per layout below.3. Install 1x6-8' fascia in

Step 16 Install Front Gable Soffit and Door Trim1. Install 86-1/4" long 2x4s under the roof sheathing, against the front gable.2. Install 86-1/4&

AirSpaceTrussShingles1x6 FasciaFeltPaper1x6 Gable TrimInstall siding according to the manufacturer'sinstructions.Install 1x6 trim on the rear gab

Frame Walk-in Door OpeningFrame Window Openingfor 18" x 36" Aluminum Window1. Cut (2) two 80-1/2" long header supports from 84"wal

Material Packaged In Component KitMaterial Supplied by Local Supplier4 1 lb. box 10d Sinkers4 1 lb. box 8d Galv.3 1 lb. box 7d Sinkers1 1 lb. box 6

Vinyl Siding OverviewStarter StripTool ListHammer & Phillips ScrewdriverFraming Square & LevelHand or Circular SawPower Drill/ScrewdriverMeasu

1. Cut (17) seventeen 2x4-12' treated boards to 11' 8-7/8". These will be the floor joists.2. Stagger the 4x4 timbers as shown below

Step 1 Assemble TrussesBuilding Tip: To aid in the assembly of the trusses, temporarily screw 2x4 blocks tothe floor. There are short 2x4s, that may h

72" long 2x43/4" Plywood GussetStep 2 Assemble Roof Gables1. Butt (2) two 72" long 2x4s together and secure by nailing a 3-1/2" x

Install Siding on Ends47-1/2" Long 2x431" Long 2x480" Long 2x4 Header Support1. Install (3) three 2x4-7' wall studs between a 31&q

AABBXXXXXX2. Install 2x4-7' wall studs between the top and bottom plates. Assemble wall frameswith 10d sinkers, two (2) nails at each stud end. N

Step 6 Assemble 10' Long Sidewalls4. Cut (3) three siding panels to a length of 87-1/4". Cut one of the panels in half lengthways.5. Square

Step 7 Assemble Door HeaderStep 8 Set Walls1. Set the back wall panel between the sidewalls. Secure wall panels together at the corners.Use (4) four 1